Improved all Examples by adding reports

_unittest/test_12_PostProcessing.py

@@ -213,6 +213,20 @@ def test_09_manipulate_report(self):
         if not is_ironpython:
             assert data.plot(is_polar=True)
             assert data.plot_3d()
+        self.field_test.modeler.create_polyline([[0, 0, 0], [0, 5, 30]], name="Poly1", non_model=True)
+        variations2 = self.field_test.available_variations.nominal_w_values_dict
+        variations2["Theta"] = ["All"]
+        variations2["Phi"] = ["All"]
+        variations2["Freq"] = ["30GHz"]
+        variations2["Distance"] = ["All"]
+        assert self.field_test.post.create_report(
+            "Mag_E",
+            self.field_test.nominal_adaptive,
+            variations=variations2,
+            primary_sweep_variable="Distance",
+            context="Poly1",
+            report_category="Fields",
+        )
         assert data.primary_sweep == "Theta"
         assert data.data_magnitude("GainTotal")
         assert not data.data_magnitude("GainTotal2")

_unittest/test_21_Circuit.py

@@ -118,6 +118,7 @@ def test_08_import_mentor_netlist(self):
 
     def test_09_import_netlist(self):
         self.aedtapp.insert_design("SchematicImport")
+        self.aedtapp.modeler.schematic.limits_mils = 5000
         assert self.aedtapp.create_schematic_from_netlist(os.path.join(self.local_scratch.path, netlist1))
 
     def test_10_import_touchstone(self):

examples/00-EDB/03_5G_antenna_example.py

@@ -214,9 +214,28 @@ def points(self):
 
 
 ###############################################################################
-# Solve Setup
-#
+# Solve Setup and create results
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+# Solves the project and create report.
+
 h3d.analyze_nominal()
 h3d.post.create_report(["db(S({0},{1}))".format(port_name, port_name)])
+
+
+###############################################################################
+# Plot Results Outside Electronics Desktop
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+# This example plots results using matplotlib.
+
+solution = h3d.post.get_solution_data(["S({0},{1})".format(port_name, port_name)])
+solution.plot()
+
+###############################################################################
+# Close AEDT
+# ~~~~~~~~~~
+# After the simulaton is completed, you can close AEDT or release it using the
+# :func:`pyaedt.Desktop.release_desktop` method.
+# All methods provide for saving the project before exiting.
+
 h3d.save_project()
 h3d.release_desktop()

examples/02-HFSS/HFSS3DLayout_Via.py

@@ -94,6 +94,16 @@
 traces = h3d.get_traces_for_plot(first_element_filter="Port1")
 h3d.post.create_report(traces, families_dict=h3d.available_variations.nominal_w_values_dict)
 
+###############################################################################
+# Create Report outside AEDT
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~
+# Create Report using Matplotlib.
+traces = h3d.get_traces_for_plot(first_element_filter="Port1", category="S")
+
+solutions = h3d.post.get_solution_data(expressions=traces)
+solutions.plot(math_formula="db20")
+
+
 ###############################################################################
 # Close AEDT
 # ~~~~~~~~~~

examples/02-HFSS/HFSS_Dipole.py

@@ -117,6 +117,36 @@
     report_category="Far Fields",
 )
 
+###############################################################################
+# Postprocessing
+# --------------
+# The same report can be obtained outside electronic desktop with the
+# following commands.
+
+solutions = hfss.post.get_solution_data(
+    "GainTotal",
+    hfss.nominal_adaptive,
+    variations,
+    primary_sweep_variable="Theta",
+    context="3D",
+    report_category="Far Fields",
+)
+
+###############################################################################
+# 3D Plot
+# -------
+# plot_3d method created a 3d plot using matplotlib.
+
+solutions.plot_3d()
+
+###############################################################################
+# 2D Plot
+# -------
+# plot method created a 2d plot using matplotlib. is_polar boolean let you
+# decide if a polar plot or rectangular plot has to be created.
+
+solutions.plot(math_formula="db20", is_polar=True)
+
 ###############################################################################
 # Close AEDT
 # ~~~~~~~~~~

examples/02-HFSS/SBR_Example.py

@@ -93,5 +93,27 @@
     context="ATK_3D",
     report_category="Far Fields",
 )
+
+###############################################################################
+# Plot Results Outside Electronics Desktop
+# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+# This example plots results using matplotlib.
+
+solution = target.post.get_solution_data(
+    "GainTotal",
+    target.nominal_adaptive,
+    variations=variations,
+    primary_sweep_variable="Theta",
+    context="ATK_3D",
+    report_category="Far Fields",
+)
+solution.plot()
+
+
+###############################################################################
+# Close and Exit Example
+# ~~~~~~~~~~~~~~~~~~~~~~
+# Release desktop and close example.
+
 if os.name != "posix":
     target.release_desktop()

examples/02-Maxwell/Maxwell2D_Transient.py

@@ -105,9 +105,6 @@
 # ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 # This example creates the output and then plots it using PyVista.
 
-import time
-
-start = time.time()
 cutlist = ["Global:XY"]
 face_lists = rect1.faces
 face_lists += rect2.faces
@@ -124,6 +121,14 @@
     export_gif=True,
 )
 
+###############################################################################
+# Postprocessing
+# --------------
+# The same report can be obtained outside electronic desktop with the
+# following commands.
+
+solutions = maxwell_2d.post.get_solution_data("InputCurrent(PHA)", domain="Time", primary_sweep_variable="Time")
+solutions.plot()
 
 ###############################################
 # Close AEDT

examples/02-Maxwell/Maxwell3DTeam3.py

@@ -133,27 +133,48 @@
 
 ###############################################################################
 # Plot mag(Bz) as a function of frequency for both coil positions
-Plot = M3D.odesign.GetModule("ReportSetup")
-Plot.CreateReport(
-    "mag(Bz) Along 'Line_AB' Offset Coil",
-    "Fields",
-    "Rectangular Plot",
-    "Setup1 : LastAdaptive",
-    ["Context:=", "Line_AB", "PointCount:=", 1001],
-    ["Distance:=", ["All"], "Freq:=", ["All"], "Phase:=", ["0deg"], "Coil_Position:=", ["-20mm"]],
-    ["X Component:=", "Distance-60mm", "Y Component:=", ["mag(Bz)"]],
+variations = {"Distance": ["All"], "Freq": ["All"], "Phase": ["0deg"], "Coil_Position": ["-20mm"]}
+M3D.post.create_report(
+    expressions="mag(Bz)",
+    report_category="Fields",
+    context="Line_AB",
+    variations=variations,
+    primary_sweep_variable="Distance",
+    plotname="mag(Bz) Along 'Line_AB' Offset Coil",
 )
 
-Plot.CreateReport(
-    "mag(Bz) Along 'Line_AB' Centred Coil",
-    "Fields",
-    "Rectangular Plot",
-    "Setup1 : LastAdaptive",
-    ["Context:=", "Line_AB", "PointCount:=", 1001],
-    ["Distance:=", ["All"], "Freq:=", ["All"], "Phase:=", ["0deg"], "Coil_Position:=", ["0mm"]],
-    ["X Component:=", "Distance-60mm", "Y Component:=", ["mag(Bz)"]],
+variations = {"Distance": ["All"], "Freq": ["All"], "Phase": ["0deg"], "Coil_Position": ["0mm"]}
+M3D.post.create_report(
+    expressions="mag(Bz)",
+    report_category="Fields",
+    context="Line_AB",
+    variations=variations,
+    primary_sweep_variable="Distance",
+    plotname="mag(Bz) Along 'Line_AB' Coil",
 )
 
+
+###############################################################################
+# Postprocessing
+# --------------
+# The same report can be obtained outside electronic desktop with the
+# following commands.
+variations = {"Distance": ["All"], "Freq": ["All"], "Phase": ["0deg"], "Coil_Position": ["All"]}
+
+solutions = M3D.post.get_solution_data(
+    expressions="mag(Bz)",
+    report_category="Fields",
+    context="Line_AB",
+    variations=variations,
+    primary_sweep_variable="Distance",
+)
+solutions.nominal_sweeps["Coil_Position"] = -0.02
+solutions.plot()
+
+solutions.nominal_sweeps["Coil_Position"] = 0
+solutions.plot()
+
+
 ###############################################################################
 # Create a plot Mag_J, the induced current density on the surface of the ladder plate
 surflist = primitives.get_object_faces("LadderPlate")

examples/02-Maxwell/Maxwell3DTeam7.py

@@ -119,20 +119,9 @@
 # Turn off displacement currents for all parts
 # NB, Eddy effect setting is regardless ignored for stranded conductor type used in Coil
 
-test = M3D.odesign.GetModule("BoundarySetup")
-test.SetEddyEffect(
-    [
-        "NAME:Eddy Effect Setting",
-        [
-            "NAME:EddyEffectVector",
-            ["NAME:Data", "Object Name:=", "Plate", "Eddy Effect:=", True, "Displacement Current:=", False],
-            ["NAME:Data", "Object Name:=", "Coil", "Eddy Effect:=", False, "Displacement Current:=", False],
-            ["NAME:Data", "Object Name:=", "Region", "Eddy Effect:=", False, "Displacement Current:=", False],
-            ["NAME:Data", "Object Name:=", "Line_A1_B1mesh", "Eddy Effect:=", False, "Displacement Current:=", False],
-            ["NAME:Data", "Object Name:=", "Line_A2_B2mesh", "Eddy Effect:=", False, "Displacement Current:=", False],
-        ],
-    ]
-)
+M3D.eddy_effects_on("Plate")
+M3D.eddy_effects_on(["Coil", "Region", "Line_A1_B1mesh", "Line_A2_B2mesh"], False)
+
 
 ################################################################################
 # Use Fields Calculator to create an expression for Z Component of B in Gauss
@@ -313,42 +302,34 @@
     if item % 2 == 0:
         plotname = dataset[item][0:3] + "Along the Line" + dataset[item][2:9] + ", " + dataset[item][9:12] + "Hz"
         if dataset[item][9:12] == "000":
-            Plot.CreateReport(
-                plotname,
-                "Fields",
-                "Rectangular Plot",
-                "Setup1 : LastAdaptive",
-                ["Context:=", "Line_" + dataset[item][3:8], "PointCount:=", 1001],
-                [
-                    "Distance:=",
-                    ["All"],
-                    "Freq:=",
-                    [str(dc_freq) + "Hz"],
-                    "Phase:=",
-                    ["0deg"],
-                    "Coil_Excitation:=",
-                    ["All"],
-                ],
-                ["X Component:=", "Distance", "Y Component:=", [dataset[item][0:2]]],
+            variations = {
+                "Distance": ["All"],
+                "Freq": [str(dc_freq) + "Hz"],
+                "Phase": ["0deg"],
+                "Coil_Excitation": ["All"],
+            }
+            M3D.post.create_report(
+                plotname=plotname,
+                report_category="Fields",
+                context="Line_" + dataset[item][3:8],
+                primary_sweep_variable="Distance",
+                variations=variations,
+                expressions=dataset[item][0:2],
             )
         else:
-            Plot.CreateReport(
-                plotname,
-                "Fields",
-                "Rectangular Plot",
-                "Setup1 : LastAdaptive",
-                ["Context:=", "Line_" + dataset[item][3:8], "PointCount:=", 1001],
-                [
-                    "Distance:=",
-                    ["All"],
-                    "Freq:=",
-                    [dataset[item][9:12] + "Hz"],
-                    "Phase:=",
-                    ["0deg", "90deg"],
-                    "Coil_Excitation:=",
-                    ["All"],
-                ],
-                ["X Component:=", "Distance", "Y Component:=", [dataset[item][0:2]]],
+            variations = {
+                "Distance": ["All"],
+                "Freq": [dataset[item][9:12] + "Hz"],
+                "Phase": ["0deg", "90deg"],
+                "Coil_Excitation": ["All"],
+            }
+            M3D.post.create_report(
+                plotname=plotname,
+                report_category="Fields",
+                context="Line_" + dataset[item][3:8],
+                primary_sweep_variable="Distance",
+                variations=variations,
+                expressions=dataset[item][0:2],
             )
 
         # Import test data into the correct plot and overlay it with simulation results.

examples/03-Circuit/Circuit_Example.py

@@ -99,6 +99,19 @@
 aedt_app.analyze_setup("MyLNA")
 
 aedt_app.export_fullwave_spice()
+
+
+###############################################################################
+# Postprocessing
+# --------------
+# Create Report.
+
+solutions = aedt_app.post.get_solution_data(
+    expressions=aedt_app.get_traces_for_plot(category="S"),
+)
+fig = solutions.plot()
+
+
 ###############################################################################
 # Close AEDT
 # ~~~~~~~~~~

examples/04-Icepak/Icepak_Example.py

@@ -99,5 +99,6 @@
 
 plot5 = ipk.post.create_fieldplot_surface(surflist, "SurfTemperature")
 
+
 ipk.analyze_nominal()
 ipk.release_desktop(True, True)

examples/05-Q3D/Q3D_Example.py

@@ -145,6 +145,7 @@
 a.sweeps["Freq"]
 a.data_magnitude()
 a.plot()
+
 ###############################################################################
 # Close AEDT
 # ~~~~~~~~~~

pyaedt/application/AnalysisNexxim.py

@@ -120,9 +120,9 @@ def excitations(self):
         References
         ----------
 
-        >>> oModule.GetExcitations
+        >>> oModule.GetAllPorts
         """
-        ports = [p.replace("IPort@", "").split(";")[0] for p in self.modeler.oeditor.GetAllPorts()]
+        ports = [p.replace("IPort@", "").split(";")[0] for p in self.modeler.oeditor.GetAllPorts() if "IPort@" in p]
         return ports
 
     @property