Define relocations for ULEB128 value: R_RISCV_SET_ULEB128 and R_RISCV_SUB_ULEB128

ULEB128 has used in DWARF and exception handling table, it used to
record value, or record the distance between two symbols.

The later one would be an issue for debug info and exception handling
table, since the symbol address might updated during, then the value
might incorrect after relaxation, some of those field has alternative
encoding type, but some new field defined in DWARF 5 ins't provide
alternative format other than ULEB128, e.g. DW_RLE_offset_pair,
DW_RLE_startx_length, DW_RLE_startx_endx and DW_RLE_start_length.

This PR basically same as #162, but updated to the trunk,
and also document ULEB128 should not shrink the size of the data,
since we never know the data used in where and does the length has
recorded in somewhere or not, so this would be most safe way.

binutils patch: https://sourceware.org/pipermail/binutils/2020-January/109672.html

Author: kito-cheng

riscv-elf.adoc

@@ -447,7 +447,11 @@ Description:: Additional information about the relocation
                                             <| `ifunc_resolver(B + A)`
 .2+| 59      .2+| PLT32         .2+| Static  | _word32_          .2+| 32-bit relative offset to a function or its PLT entry
                                             <| S + A - P
-.2+| 60-191  .2+| *Reserved*                          .2+| -       |                   .2+| Reserved for future standard use
+.2+| 60      .2+| SET_ULEB128   .2+| Static  | _ULEB128_         .2+| Local label assignment <<uleb128-note,*note>>
+                                            <| S + A
+.2+| 61      .2+| SUB_ULEB128   .2+| Static  | _ULEB128_         .2+| Local label subtraction <<uleb128-note,*note>>
+                                            <| V - S + A
+.2+| 62-191  .2+| *Reserved*                          .2+| -       |                   .2+| Reserved for future standard use
                                             <|
 .2+| 192-255 .2+| *Reserved*                          .2+| -       |                   .2+| Reserved for nonstandard ABI extensions
                                             <|
@@ -460,6 +464,12 @@ This section and later ones contain fragments written in assembler. The precise
 assembler syntax, including that of the relocations, is described in the
 _RISC-V Assembly Programmer's Manual_ <<rv-asm>>.
 
+[[uleb128-note]]
+NOTE: The assembler must allocate enough space to accommodate ULEB128 data for
+`R_RISCV_SET_ULEB128` and `R_RISCV_SUB_ULEB128` relocations. This can be
+achieved either by padding with zeroes to fill up to the XLEN-bits boundary
+or by filling the precomputed result into the relocation location.
+
 ==== Calculation Symbols
 
 <<var-reloc-calc>> provides details on the variables used in relocation
@@ -501,6 +511,7 @@ of the `__global_pointer$` symbol into register `gp` (aka `x3`).
 | _word16_    | Specifies a 16-bit word
 | _word32_    | Specifies a 32-bit word
 | _word64_    | Specifies a 64-bit word
+| _ULEB128_   | Specifies a variable-length data encoded in ULEB128 format.
 | _wordclass_ | Specifies a _word32_ field for ILP32 or a _word64_ field for LP64
 | _B-Type_    | Specifies a field as the immediate field in a B-type instruction
 | _CB-Type_   | Specifies a field as the immediate field in a CB-type instruction
@@ -1221,6 +1232,14 @@ are commonly resolved at compile-time, such as intra-function jumps), code
 generators must in general ensure that relocations are always emitted when
 relaxation is enabled.
 
+Linkers should adjust relocations that refer to symbols whose addresses have
+been updated.
+
+ULEB128 value with relocation must be padding to the same length even if the
+data can be encoded with a shorter byte sequence after linker relaxation, The
+linker should report errors if the length of ULEB128 byte sequence is more
+extended than the current byte sequence.
+
 === Linker Relaxation Types
 
 The purpose of this section is to describe all types of linker relaxation,