Replies: 18 comments 37 replies
-
|
hi just updated, my devices are working fine and logs show devices alive, but dashboard shows flashing offline? EDIT: My devices are not working, mqtt part is not updating. EDIT 2: I rebooted the addon, and now my zigbee network is working, but still flashing offline on the dashboard. EDIT 3: my problem is solved following these instructions: #26942 (comment) EDIT 4: No issues to report with 2.2.1
|
Beta Was this translation helpful? Give feedback.
-
|
Unfortunately I am not a programmer. So I will write. Today after the update all devices have the status "unavailable". However, all devices work, the map is built normally (Tuya, z2m 2.2.0-1 ) |
Beta Was this translation helpful? Give feedback.
-
|
Actually, my devices are not working in mqtt, only see them in the addon log. |
Beta Was this translation helpful? Give feedback.
-
|
Same issue please let me know if there is something I can do (supply some logging or such) ttyACM0 /dev/serial/by-id/usb-Texas_Instruments_TI_CC2531_USB_CDC___xxxxxxxxxxxxxxxxxx-xxxx |
Beta Was this translation helpful? Give feedback.
-
|
Same here, & devices not working. Rolled back to previous version. |
Beta Was this translation helpful? Give feedback.
-
|
so its like everything is working, but nothing is working, for example:
But, I cannot turn off a switch. |
Beta Was this translation helpful? Give feedback.
-
|
Z2m 2.2.0 upgrade introduce a new revision of zigbee-herdsman-converters. |
Beta Was this translation helpful? Give feedback.
-
|
same for me |
Beta Was this translation helpful? Give feedback.
-
|
Is there any plan to fix the connection for the Lutron Aurora's? I have 20 of them around the house literally just waiting till that gets fixed but starting to think it may soon be time to swap them out for something that still works. |
Beta Was this translation helpful? Give feedback.
-
|
same problem |
Beta Was this translation helpful? Give feedback.
-
|
Exact same problem here |
Beta Was this translation helpful? Give feedback.
-
|
Cannot run OTA Updates for Sonoff TRVZB - Update request fail |
Beta Was this translation helpful? Give feedback.
-
|
Do you have more than 1 device and are they all affected? I already have 1.3.0 installed so cannot test, but curious for future updates. |
Beta Was this translation helpful? Give feedback.
-
|
i have 9 Devices and all are affected |
Beta Was this translation helpful? Give feedback.
-
|
I have 6 such devices and I have no problem - OTA can be carried out successfully - for example: |
Beta Was this translation helpful? Give feedback.
-
|
so it worked when they added the external temperature sensor value and it stopped working when they added hysteresis that has 1.3.0 as a requisite. donno if its related. |
Beta Was this translation helpful? Give feedback.
-
checking works for me as well, I guess the issue is with actually installing the update. |
Beta Was this translation helpful? Give feedback.
-
|
All too
Le mer. 2 avr. 2025, 10:27, NLand99 ***@***.***> a écrit :
… i have 9 Devices and all are affected
—
Reply to this email directly, view it on GitHub
<#26935 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AFTRHETOPZCL4AJJZUEXGQT2XONQTAVCNFSM6AAAAAB2HU7HRSVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENRZG43TKNQ>
.
You are receiving this because you commented.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
Since this version Zigbee2MQTT cannot run anymore for me: [02/04/2025 10:38:23] error: z2m: Could not init sd_notify: Could not locate the bindings file. Tried:
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/build/unix_dgram.node
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/build/Debug/unix_dgram.node
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/build/Release/unix_dgram.node
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/out/Debug/unix_dgram.node
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/Debug/unix_dgram.node
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/out/Release/unix_dgram.node
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/Release/unix_dgram.node
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/build/default/unix_dgram.node
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/compiled/22.14.0/linux/arm64/unix_dgram.node
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/addon-build/release/install-root/unix_dgram.node
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/addon-build/debug/install-root/unix_dgram.node
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/addon-build/default/install-root/unix_dgram.node
→ /opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/unix-dgram/lib/binding/node-v127-linux-arm64/unix_dgram.nodeI run Zigbee2MQTT on ARMBian using an Odroid N2+, Linux installation method. |
Beta Was this translation helpful? Give feedback.
-
|
Can you try this? pnpm i --frozen-lockfilepnpm rebuild unix-dgram |
Beta Was this translation helpful? Give feedback.
-
|
Let's continue in #26946 |
Beta Was this translation helpful? Give feedback.
-
I should not have downgraded and make an installation from scratch and waited for the suggestion, after a second update Zigbee2MQTT runs again. |
Beta Was this translation helpful? Give feedback.
-
|
After update all of my devices marked Offline:
If you check the avilability settings, it is unsettable:
|
Beta Was this translation helpful? Give feedback.
-
|
Fixed! Changes will be available in the dev branch in a few hours from now and in the hot fix release (will release it in the coming days) |
Beta Was this translation helpful? Give feedback.
-
|
same here |
Beta Was this translation helpful? Give feedback.
-
|
Same here, but pay attention! it appears all is working ok. but with a Sonoff sensor the temperature showing in display is different than the one is showing in HA so it appears not updating ok. Reversed to 2.1.3-1 it backs updating ok. |
Beta Was this translation helpful? Give feedback.
-
|
back to 2.1.3 all is good. |
Beta Was this translation helpful? Give feedback.
-
|
Meaning "try and see" more likely, yes? |
Beta Was this translation helpful? Give feedback.
-
|
wait for a new version without this bug |
Beta Was this translation helpful? Give feedback.
-
|
Jim How did you roll it back to 2.1.3? |
Beta Was this translation helpful? Give feedback.
-
|
Before upgrading to the new version, I use the HA feature, which allows me to back up the current version. |
Beta Was this translation helpful? Give feedback.
-
|
Awe ok... I wasnt able as i did not download back up phone would not allow.... Thanks for the fast response! |
Beta Was this translation helpful? Give feedback.
-
|
What a fantastic version! First time a version is a nightmare for me, but this first one is a big one! |
Beta Was this translation helpful? Give feedback.
-
|
did you try reverting to the previous version? the crap part with PanId is that you might need to re-pair your devices. |
Beta Was this translation helpful? Give feedback.
-
|
I finaly succeeded in having my network again without repairing by:
I rolled back to 3.1.3, with no success until I deleted everything except config in /opt/zigbee2mqtt then reinstalled Zigbee2MQTT which now starts again using SystemD. |
Beta Was this translation helpful? Give feedback.
-
|
For comparison, I updated to 2.2.0 with no apparent issues. I am running Z2M in a docker, with MQTT in HA. I have mostly Third Reality devices, lights and plugs. Running a coordinator UZG-01 with the XZG firmware 20240710, also a router UZG-01 with the XZG firmware 20240909 |
Beta Was this translation helpful? Give feedback.
-
|
I had the same issue with all devices shown as offline. Deleted zigbee2MQTT and installed it again. Now it won't even start the program: [16:03:47] INFO: Preparing to start... |
Beta Was this translation helpful? Give feedback.
-
|
Upgrayedd to 2.2.0 yesterday and all is looking fine. Will check back in in a week or two. |
Beta Was this translation helpful? Give feedback.
-
|
Works well for me as well. Running in a container on rootless Podman. |
Beta Was this translation helpful? Give feedback.
-
|
Hi, I updated through ./update.sh as usual. However after the successful update I cannot access zigbee2mqtt through the usual IP. It's not working any more. When I roll back to previous version it recovers just fine. error: TypeError: Module "file:///opt/zigbee2mqtt/package.json" needs an import assertion of type "json" What can I do? |
Beta Was this translation helpful? Give feedback.
-
|
Updating to 2.2.1 did not solve the problem... |
Beta Was this translation helpful? Give feedback.
-
|
did you read the patch notes? check this out #26937 |
Beta Was this translation helpful? Give feedback.
-
|
Thank you so much! That did the trick!!! |
Beta Was this translation helpful? Give feedback.
-
|
The patch works ! |
Beta Was this translation helpful? Give feedback.
and others
-
Feel free to discuss the 2.2.0 and 2.2.1 release here!
Note that 2.2.1 is a hot-fix release to fix various issues introduced in 2.2.0.
Beta Was this translation helpful? Give feedback.
All reactions